| Personalising the Codan 9323, 9360 and 9780 transceivers | |||
| (Thanks to Peter Harland of QLD) | |||
| Setup PROCEDURE | |||
| Enter setup mode by pressing the MODE button on the control panel 4 (four) times. Use mircophone keypad to enter Setup code: | |||
| Procedure | Setup code | Description | Setting - Comment |
| BEEP LOUDNESS | 33 | change the volume of the beeps by the transceiver | NORMAL (selectable) |
| CALL PREAMBLE LENGTH | 242 | sets the length of the preamble transmitted at the start | select SELCALL - if ALE is not fitted |
| of a selcall | |||
| CALL PRIVACY | 2443 | limits stations that can receive your GPS, Page call and | OFF - unless you have a specific reason to enable privacy |
| Status call transmissions | |||
| CLOCK CALIBRATION | 412 | calibrates the transceiver clock against a external standard | - adjusts time gain or loss |
| CLOCK SETTING | 411 | sets time and date of the transceiver clock | |
| DISPLAY BRIGHTNESS | 311 | changes brightness of display | |
| DISPLAY CONTRAST | 312 | changes contrast of display | |
| DISPLAY DIAGNOSTICS | 314 | switches on or off the diagnostics display of the transceiver | if ON it replaces the channel info (tag) |
| DISPLAY FREQUENCY | 313 | set how the frequency is displayed for each channel | Rx/Tx |
| FREE TUNE RECEIVER | 3442 | turns on/off ability to free tune receiver | |
| PAGE CALL MESSAGE SETUP | 24441 | can store up to 3 pre recorded messages for sending | except Version 1 Firmware |
| POWER UP MESSAGE | 34411 | allows for message to be displayed for a few moments when | optional personal message |
| transceiver first starts up | |||
| POWER UP MUTE | 34412 | selects initial mute setting on start up | select SELCALL, VOICE mute or NONE |
| POWER UP ADDRESS | 34413 | shows self I.D. (your selcall) on startup | shows/hide your selcall |
| PTT RELEASE BEEP | 3432 | switches on/off PTT release beep | saves saying "OVER" - other party hears a "BEEP" instead |
| PTT TRANSMIT CUTOUT | 3431 | prevents transceiver being left on transmit state | set time - transceiver protection |
| POWER OUTPUT | 3433 | sets ability to select power output level - 10 or 100W | ENABLE - not available on Version 1 firmware |
| RECALL CHANNEL BY FREQUENCY | 32 | enables recall channels by frequency | ON -recalls either by frequency or channel number |
| RF GAIN | 3443 | switches on RF gain | ON - transceiver is more sensitive to low strength signals |
| SELCALL ID | 211 | setup selcall and telcall ID's - up to 5 ID's | assign ID |
| SELCALL SIZE | 213 | sets selcall ID size - 4 or 6 digits | check with network provider |
| STATUS CALL AVAILABILITY | 24442 | allows you send and receive diagnostic, config and user calls | ON - not available with Version 1 firmware |
| TELCALL AVAILABILITY | 22 | switches on ability to make telcall (phone calls) | ON |
| IF GPS OPTION is AVAILABLE and GPS connected | |||
| GPS DISPLAY | 3421 | switches on the display of your GPS location | ENABLE - replaces Channel tag info |
| GPS TIMEOUT | 3422 | GPS timeout warning | DISABLE |
| RS-323 CONNECTED EQUIPMENT | 3411 | identifies equipment connected to either the RS-232 or GP | select GPS NMEA-0183 |
| ports - on back of transceiver | |||
| RS-232 BAUD RATE | 3412 | synchronise speed for information transfer | set 4800 ( check GPS receiver baud rate - typically 4800) |